• vol v rev 0 | specification (technical standard) | electrical

    Vol V Rev 0 | Specification (Technical Standard) | Electrical

    DESEIN. Vol-V : Instrumentation & Control Works. SPECIFICATION FOR EPC CUM DEBT FINANCING CONTRACT VOLUME V INSTRUMENTATION & CONTROL WORKS CHAPTER-1 GENERAL INFORMATION 1.01.00 Information to Be Furnished With the Offer The bidder shall furnish the following documents/drawings along with the Bid: Complete Specification/data sheets, bill of material of instruments, equipment and accessories

  • guidance on the biocidal products regulation

    Guidance on the Biocidal Products Regulation

    Guidance on BPR: Volume V Guidance on applications for technical equivalence Version 2.0 July 2018 11 Standard term / Abbreviation Explanation UVCB-reference UVCB active substance from the reference source v/v Volume per volume ratio vPvB Very persistent and very bioaccumulative

  • joint fleet maintenance manual

    JOINT FLEET MAINTENANCE MANUAL

    Volume V - Quality Maintenance (formerly Quality Assurance) 3 PURPOSE. This manual serves as: a. A standardized, basic set of minimum requirements to be used by all Type Commanders and subordinate commands. b. Clear, concise technical instructions to ensure maintenance is planned, executed, completed and documented within all Fleet commands. c.

  • medium voltage technical guide - electrical engineering portal

    Medium Voltage technical guide - Electrical Engineering Portal

    specifications" incorporates a note in its scope: "For the use of this standard, high voltage (see IEV 601-01-27) is the rated voltage above 1000 V. However, the term medium voltage (see IEV 601-01-28) is commonly used for distribution systems with voltages above 1 kV and generally applied up to and including 52 kV.".

  • introduction to codes and standards for instrumentation

    Introduction to Codes and Standards for Instrumentation

    Technical Article Introduction to Codes and Standards for Instrumentation and Controls Engineers March 26, 2020 by Dennis Lynch Regardless of the industry, or your role in that industry, codes and standards are an integral part of the environment in which we work and have a major influence on design and engineering.

  • urban electric vehicle (uev) technical specifications

    Urban Electric Vehicle (UEV) Technical Specifications

    TECHNICAL SPECIFICATIONS (22) Propulsion power shall be isolated from the vehicle chassis such that leakage current does not exceed 0.5 MIU. Charging circuits shall be isolated from the vehicle chassis such that ground current from the grounded chassis does not exceed 5 mA at any time the vehicle is connected to an off-board power supply.

  • guidance on the biocidal products regulation

    Guidance on the Biocidal Products Regulation

    Guidance on BPR: Volume V Guidance on applications for technical equivalence Version 2.0 July 2018 11 Standard term / Abbreviation Explanation UVCB-reference UVCB active substance from the reference source v/v Volume per volume ratio vPvB Very persistent and very bioaccumulative

  • i1700 datasheet rev 1.3-s2

    I1700 Datasheet Rev 1.3-s2

    VOL Volume: This control has 8 levels of volume adjustment. R OSC Oscillator Resistor: A resistor determines the sample frequency of the device, which sets the duration. V CCA Analog Power Supply. Power supply for analog circuitry. FT Feed-through: Enable the feed-through path for AnaIn signal to the outputs.

  • ps9313l, ps9313l2 data sheet

    PS9313L, PS9313L2 Data Sheet

    Terminal Capacitance Ct V = 0 V, f = 1 MHz 30 pF Detector Low Level Output Voltage VOL IF = 10 mA, IOL = 2.4 mA 0.13 0.6 V High Level Output Current I OH VCC = 20 V, VF = 0.8 V 1.0 50 A High Level Supply Current ICCH VCC = 20 V, VF = 0.8 V, VO = open 0.6 1.3 mA

  • piezoelectric alarms

    PIEZOELECTRIC ALARMS

    V= with Volume Control Min V Max V Type At Min V At Max V Center Hz. Range ±Hz. Hz. At Min V At Max V Part Number Loudness Category Operating Voltage Typical SPL at 24 inch (61cm) dB(A) Sound Frequency Rate ±20% Operating Current mA Termination Plastic Housing Style V= with Volume Control Min V Max V Type At Min V At Max V Center Hz. Range

  • ts1002/ts1004

    TS1002/TS1004

    TS1002/4 Rev. 1.0 Page 3 ELECTRICAL CHARACTERISTICS VDD = +0.8V, VSS = 0V, VINCM = VSS; RL = 100kΩ to (VDD-VSS)/2; TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C. See Note 1 Parameters Symbol Conditions Min Typ Max Units Supply Voltage Range VDD-VSS 0.65 0.8 2.5 V Supply Current ISY TS1002; RL = Open circuit

  • the datasheetarchive - datasheet search engine

    The DatasheetArchive - Datasheet Search Engine

    supply voltage for logic vdd -vss - 4.75 5.0 5.25 v supply voltage for lcd vdd –vee (vlcd) - - 12.0 - v input high vol vih-v dd-2.2 - vdd v input low vol vil-0-0.8v output high vol voh-v dd-0.3 - vdd v output low vol. vol-0-0.3v supply current for logic *idd - - 15.0 25.0 ma used ic t6963c & t6a39 & t6a40 *idd measurement condition is for all